cliffyv's Vehicle Feed
Basic Specifications
Vehicle Color: BlackEngine Type: 8 Cylinder
Transmission: Manual
Est. Horsepower: 530 HP
Est. Curb Weight: 3,700 lbs.
Mileage: 50,000 miles
At the Track
Best 60': 2.1Best R/T:
Best 1/8 Mile ET:
Best 1/8 Mile MPH:
Best 1/4 Mile ET: 11.90
Best 1/4 Mile MPH: 126
cliffyv's Other Current Vehicles
Sites in the FQuick Network
Get your forum exposure. Click here and join for FREE!cliffyv's 1999 Pontiac Trans Am WS6
Built by Myself
About this Current Vehicle:
This car was all built by myself and friends. We built the engine, minus shortblock. From engine and transmission installation/fabrication to the 8 point, the rear, the suspension, the exhaust, interior, gauges. It is even efilive tuned by myself.
The stereo and the remainder of the interior is to come
The project is still ongoing, if i could find time to hook up all of the nitrous stuff and get the interior installed..
Vehicle Journal:
Oct 08
Beaver Run Oct 5th
Took the car to the 1/4 for the first time since its rebirth. It was terrible. With drag radials the car was spinning through 4th. The fastest time was launching at idle and babying it til 3rd. That was a 2.1 60 foot, 11.90 @ 126.
Mar 23
March 23, 2008
Ok i havent updated this nor took any pictures in a while. Here is the current status. I have finally finished all the nitrous crap. The bottle is in, the wiring for the bottle heater, remote opener, the heater pressure switch done. The 1st stage plate setup is wired and plumbed, along with the pressure safety switch, window switch and WOT switch. I installed my spohn drag sway bar, nice piece. i got Tim Tosto's valve covers but they dont work, too tall when you have HVAC. So ive ordered Nasty Relocation coil brakets and had a set of custom wires made... SWEET. So ill update with pics soon. Next is the rear view mirror tv for the backup camera and the indash, carpet, and all the interior plastic. I also need to get my seats in, im hyped to get those installed.
Feb 02
Feb 1, 2008
I havent had much time to work on the car, been so busy.
Adding the 2 stages of nitrous. Harris Speed works 90MM plate and dry shot. Wiring the Window switch, WOT switch, Fuel pressure safety switch, Illuminated purge and all the noids. Then its off to the master switch and HSW bottle heater and NOS remote opener. Yikes What did i get myself into. I think i added 50 LBS of wiring.
Factory Options:
All
Exterior Modifications:
Tint
Interior Modifications:
Custom 8 Point and NO2 bottle mount Danimal Fabrications Shippensburg, PA
Corbeau Microfiber seats
Triple gauge pod and gauges
Suede interior Speed of Sound Harrisburg PA
15LB NOS bottle, NOS remote opener, Harris Speed Works Heater, Nitrous Outlet master switch.
Performance:
Iron 402 Eagle crank/rods Ross pistons AFR 205 Comp pushrods/Lifters Patriot Performance double springs/titanium retainers Texas Speed Magic Stick v.3 camshaft Harland Sharp modded lsx rocker arms SLP double timing set Fast 90Intake/90Throttle Body SLP Oil Pump LS6 Valley Cover EFiLive V2 Meziere Water Pump Ford Motorsport 42lb injectors Nasty FuelRails/lines Edelbrock Stainless Steel LT/Y Magnaflow Catback QTP Electric cutout Racetronix Pump/Hotwire Kit ARP Head/Header studs Rod, Main, crank, rocker arm, valley bolts
GoodYear gatorback Serpentine belt
Harris Speed Works 90MM Plate, NOS Dry shot in lid, NX illuminated Purge, HSW Fuel Pressure Safety Switch, MSD window switch.
Suspension/Chassis:
Torque Thrust II's 17x9Front 17/11Rear BMR Sub-Frame connectors Torque Arm Spohn relocation brackets SJM Manufacturing Adjustable Lower Control arms to my specs and adjustable pan-hard bar.
Drilled rotors and Hawk Brake pads
Drivetrain:
Moser 12 bolt with aluminum pinion support cover
Dennys Nitrous Ready DS Spec stage IV clutch/billet flywheel ARP Flywheel/PressurePlate bolts
ARP wheel studs
Pro-5.0 shifter and Lou's short Stick
Electronics:
Stereo In progress
Speed of Sound Harrisburg PA
To-Do List:
N/A
Copyright © 2008 FQuick.com. Terms of Use & Privacy Policy
7 Comments on cliffyv's Trans Am WS6
Actually forgot to take that out, I was planning on picking up some eu700s, my friend has them in his maro and there pretty damn nice and well hidden but after my stockers blew I found at the last minute replacement for $20 for both sail panels so I picke
That is one sick Tranny. Great job, can't wait to see finished project!
Nice T/A! Do you ever go to Mason-Dixon or other track?
Thanks for the comments. The tailllights are candied. They use candy to darken them, I'm not big on covers.
Nice list of mods, it's cool to do it yourself
AWESOME
Damn dude your good.