44too's 1968 Oldsmobile 442

torn between keeping or selling, need something more streetable

About this Vehicle for Sale:

TRADES????????????

$9900

Clear TN Title, REAL 442

Been putting it together for 2 (2 many) years, haven’t been anywhere with it, don’t care anymore, fed up…

Fiberglass:

Pin on 4” Cowl hood
Pin on Deck lid
Bumpers

Body:

Doors have minor rust in front lower (not all the way to the edge, easy fix)
Fenders’ lower rear patches repair started, need finishing
Body is straight, frame is SOLID.
Original vinyl roof car, had new roof welded on, NO RUST
ALL good glass
Headlamp housings need some finesse
Trim removed, but still have it.
Powdercoated 4 core radiator support and fenders

Interior:
Correct ’68 front seats
Cracked dash w/ Factory speedo, fuel level oil/water/amp idiot light, and gauge blank
A/C removed, but still have parts
Stewart Warner Performance Oil/Water/Volts
Autometer 2 stage Shift Lite/Tach
Autometer Trans Temp
Autometer Lunar Fuel Level
Autometer Carbon ELECTRICAL Nitrous Pressure
Hurst Quarter Stick Pistol grip shifter w/ TCI line lock, bracket made so factory console can be used, included.
3 spoke original look wheel (Grant)
Steering column is ’68, but for column shift
Trunk mount battery w/ cut off switch and HD solenoid

10 gallon Fuel Cell w/ sump, foam, GM sender
8AN braided fuel line to Holley Blue pump, WIX filter, Mallory Regulator
800CFM Q-jet (for now, may change to a Holley)
Stewart Warner Performance Fuel Pressure gauge

Engine:

Offy Port-O-Sonic Intake, opened up for Q-jet
FRESH 0 miles G Heads with massive Ferrea valves, Comp Springs, bronze guides, port work/bowl work, surfaced
Harland Sharp Roller Rockers
Corteco .028 head gaskets
FRESH short block 461, CP forged LIGHT pistons, reconditioned rods, Nodular crank, Milodon pan
Hooker 1 ¾” primaries, 3” collector headers, Jet-Hot coated
3” H-pipe w/ Dynomax 3” mufflers
Northern 31X19 Aluminum Radiator
Custom powdercoated satin black aluminum catch can, with solenoid activated drain. (I had an extra nitrous solenoid laying around, and didn’t feel like buying a petcock)
Flex-A-Lie Dual Fans to separate relays
Meziere HD Water Pump
CSR Mini Starter
Performance HEI Distributer and Coil
BOP Engineering Alternator mount
SFI Balancer (proform)
RamAirBox 14X3 Air Cleaner to Aluminum Headlight funnels
NOS 125 non adjustable kit w/ purge, Hobbs switch, pressure regulated heater, remote bottle opener, Custom Rocket logo bottle blanket

Trans:

FRESH built TH400, ATD 9” 4200 stall (http://www.autotransdesign.com/motorsports/index.html)
deep aluminum pan w/ filter extension
B&M Transpak
Poly Mount
JW Ultrabell
1350 Yoke
Flex-A-Lite 8AN transmission cooler, fittings on transmission ARE CORRECT, will not crack the case like the usual B.S. NPT fittings. ATI part # 925138 and were $40 shipped. No cutting corners when it means possibly cracking the case of a transmission you just spent HUNDREDS on, right?

Rear End:

12 Bolt Chevy w/ fresh posi, Richmond 4.10 gears, ½” studs, 1350 Yoke

NEW Driveshaft made by Drive Line Service of Jax, 1350 Joints, 3" .083 Mild Steel

FRONT Suspension/Brakes:

12" Drilled/Slotted Rotors w/ B-body spindles
Braided lines
SPC Adjustable Upper A arms
½ coil removed from left spring
¾ coil removed from right spring
Comp Eng 3 way drag shocks
Lower A Arms powdercoated
Sway bar removed
Manual Steering Box

REAR Suspension/Brakes:

Wilwood disc "drag kit"
BMR tubular lower arms
BMR adjustable uppers w/ no-hop relocation brackets
Comp Eng 3 way drag shocks

Wheels/Tires

15X5 / 15X8 Weld Pro Stars
205/70/15 BRAND NEW fronts
28X10.5 ET Drag w/ anodized screws 5 passes on a friend’s car

Alignment specs are set at 2.5" high for drag racing.